UPVC replacement upvc window handles Door Handles

The handles on your doors are worn out with time and require to be replaced. In this case, it is important that the new handles conform to the exact dimensions of the handle that was previously used.

The three measurements to be inspected are the top screw's position the lever and key hole sizes. Check the size guide for help with this.

Inline Lever/Lever

A lever/lever door handle is a contemporary handle that can be installed on new or replacement doors. This style of door handle is available in a wide range of styles & finishes. This handle is offered by several manufacturers, including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are made of robust materials and are perfect for multi-point lock doors which require a robust design. The handles for bifold doors are inline and operate with the same spindle as well as screw fixings, so they are easily installed on new or existing uPVC/Composite doors.

The sprung lever design allows the handle to be positioned and angled for comfortable operation and is suitable for all users. The handle has been tested for endurance up to 200,000 cycles. This allows for the assurance of the quality of the finish and the performance of the handle over time. The lever that is sprung can be cut to fit a wider range of locks. This is particularly useful for narrower doors where the cylinder is situated further away from the door handle replacement. A lever that is shorter can be used for doors with a latch which can be operated with the thumb on the inside.

Lever Pad

A Lever Pad door handle made of upvc functions differently to the lever type handles found on most doors. These handles are operated by one spindle or two spindles, inline or offset. They are usually utilized on UPVC doors with double glazing. They come in a variety of finishes and variations.

The handles have been tested to at least 200k cycles and are available in various finishes including White Silver, Chrome, & Gold. The finish is BS EN 1670 Grade 5 and resistant to corrosion. This provides the handle with the best performance and durability for its intended use.

All of the UPVC lever pad styles for handles come with screws and a spindle, allowing them to be fitted on a new or existing uPVC door. The backplate fixation centres of 211mm allow for a bigger handle, which is typically a benefit when replacing a window handle a damaged or old multi-point door lock mechanism. The levers for these handles have a spring, which solves the problem of handles for doors that slide out of horizontal position when not in use.

It is crucial to ensure that the PZ dimensions for both the multipoint lock as well as the uPVC doors when choosing a replacement handles for upvc windows UPVC spindle and handle. This measurement is also called 'handle centre or cylinder centres'. It is important to match the right handles.

Once you have the correct PZ size you will then have to ensure that the lever pads and push pads are a suitable shape for the American with Disabilities Act (ADA) approved handles you require for your doors. They are usually of a round or square shape, with an internal lever and an external push pad.

The majority of the UPVC Lever Pads we sell are sprung. This means they can be reverted to a horizontal position when they are not in use instead of hanging, and possibly sticking in the frame. This prevents drafts and cold air from entering a property. The majority of UPVC lever pad style handles are available in left and right handed versions that allow them to be installed on either side of the doors.

Euro Cylinder

Cylinder locks are found on uPVC and other kinds of doors. The cylinder lock operates by using a key that unlocks the cylinder's case. This reveals pins that can be aligned with the pins in the lock and allow them to turn the revolving camera, opening the door. Euro cylinders are available with up to six pins. Doors that are internal and external require different levels of security.

The choice of the correct cylinder is crucial; it is dependent on how your doors and handle are utilized. For example, external doors must be secured with an extra secure cylinder, while doors inside can be secured using an ordinary cylinder. In addition, some cylinders are available with extra features that can improve security even more, like anti-drill or anti-bump features.

A euro cylinder must be measured correctly to ensure it's the right size for your door. The cylinder should be measured from the central fixing screw hole to each end of the cylinder and the thumb turn if you have one. It is best to do this with the lock in place however when this isn't possible, you can take it off to measure. A cylinder that is protruding beyond the handle and escutcheon may be vulnerable to attacks such as snapping locks, so it is essential that it is not too long.

Most modern cylinders are designed with bump and anti-drill features that are built into their design. These features are designed to minimize the risk of attack by forcing the cylinder to rotate in a different direction. This will help to deflect the attack and keep your doors safe.

Certain cylinders are made to resist snapping. This is a common occurrence on cylinders. A specially designed tool is used to break the break line of the lock and then the front of the cylinder is snapped off. This is a faster and more convenient method of gaining access than through the use of a multipoint locking system. It also leaves no evidence of the break-in which could hinder insurance claims.

Spring Cassette

The spring cassette is positioned inside the base of your door handle backplate, supplying a spring-loaded solution and returning your multipoint lock handles to their normal position after usage. These handles used to have no spring and would drop when the locking mechanism was removed. The addition of this simple element is among the best ways to correct this issue and is a great way to prevent your doors made of upvc from getting stuck in an open or closed position, since they are not always easy to close manually.

The spring cassettes were made to be used with a sprung multipoint locks. They won't work with unsprung handles, and you will have to cut a hole into your backplate for them to fit. (Please look at the image for a detailed diagram). These cassettes are a replacement for damaged or missing cassettes in the backplate of uPVC door handles. They have a square cut-out that accommodates an 8mm spindle and are sold as a set.

These spring cassettes are an excellent value for money solution to the issue of your door handles sagging. These spring cassettes are simple to install and will increase the life of your uPVC door. Please contact our team to learn more about our range of uPVC accessories and spares. We are always happy to provide expert advice and support you.